Not all USB-C ports support all features of USB-C. Some computers and smartphones only support data over USB-C for external storage such as flash drives while some devices support video and charging over USB-C. Check the below article about the USB-C port capability. If you are not sure, please consult the manufacturer for this information.
Connecting to displays with DVI / VGA using HDMI video converter adapters:
Connecting to DVI/VGA displays through an HDMI to DVI / VGA cable is supported. The maximum resolution will be limited at 1920x1080 @ 60Hz.
Symptom: The Docking Station is not functioning properly on a Windows computer with Thunderbolt 3. Symptoms include no video, flickering video, or an unstable USB peripheral connection.
Solution: Update BIOS, Thunderbolt 3 firmware, Thunderbolt 3 driver, and Intel Graphics Driver from the manufacturer website. For more details, refer to articles below:
Symptom: Unable to achieve dual 4K video output and USB 3.1 speed at the same time
The dock utilizes a single USB-C cable to deliver video and data. Therefore, video transmission and data transmission (including USB, SD card reader, and Ethernet) share the total bandwidth that USB 3.1 Gen 2 can offer. When a single 4K@60Hz display or dual 4K@30Hz displays are connected, there is not enough bandwidth for USB 3.1 data transfer speed. In this case, USB, SD card reader, and Ethernet speed will be limited at 480Mbps.
The dock features the Dynamic Configuration Switch. It allows users to switch between 4K mode and HD mode. Under HD mode, a single 4K@30Hz display or dual 1080p@60Hz displays are supported. In this case, users can enjoy up to 10Gbps USB transfer speed, UHS-II card reader, and Gigabit Ethernet.
Symptom: Unable to achieve dual 4K video output
When switching to 4K mode, the maximum number of displays supported are listed below.
When switching to HD mode, the maximum number of displays supported are listed below:
Symptom: Second display does not light up
When connecting two 4K displays, identical display models are recommended. The first display may be default output 4K 60Hz resolution (if it supports 4K 60Hz) while the second display will only output 1080p due to insufficient bandwidth. Manually lower the refresh rate of the first display to 30Hz in
'Control Panel' > 'Display' > 'Adjust Resolution' > 'Display Adapter Properties'
Then manually increase the resolution of the second display to be 4K 30Hz.
If the second display is recognized in Windows but does not light up, most likely there is not enough bandwidth remaining for the second display. Again, manually lower the resolution of the first display and connect the second display in
'Control Panel' > 'Display' > Adjust Resolution
You may need to reconnect the HDMI cable after making this change. If you are still experiencing issues setting up two monitors, please check the article below for further DisplayPort MST troubleshooting.
Symptom: Second display mirrors the screen of the first display on a Mac computer, certain Chromebook models, and Android devices
macOS and Android do not support the DisplayPort MST technology, which is required to support extended screen on the second display through a single video port. Chromebook may support the DisplayPort MST technology depending on the model number. The Docking Station only supports duplicated external displays on a Mac computer, Android device, or certain Chromebook models that do not support the DisplayPort MST technology.
Symptom: Mouse lag or missing keystrokes when connecting a wireless mouse/keyboard to USB 3.0
The 2.4 GHz band is a widely used unlicensed radio frequency band for devices such as wireless routers and wireless PC peripherals such as a mouse or keyboard.
USB 3.0 has a 5 Gbit/s signaling rate. The noise from the USB 3.0 data spectrum can create a conflict in the 2.4–2.5 GHz range. This noise can radiate from the USB 3.0 connector on a PC platform, the USB 3.0 connector on the peripheral device, or from the USB 3.0 cable. If the antenna of a wireless device operating in this band is placed close to any of the above USB 3.0 radiation channels, it can pick up the broadband noise and cause interference. This may result in a decreased throughput on the wireless link.
The solution is to connect the wireless mouse / keyboard dongle to the USB 2.0 port on the back of the dock where the mouse/keyboard mark is located. If this still does not solve the issue, try using a USB 2.0 extension cable like this one:
Symptom: The Docking Station is not recognized or one or more ports is not functional
Unplug all cables and peripherals, restart the computer, and then reconnect everything.
Symptom: Computer does not charge or charges at a reduced speed
This Docking Station can pass up to 80 watts of power to the computer. Some computers may require more than 80 watts. These computers may disable charging through USB-C or charge at a reduced speed.
Symptom: Computer charges but all other ports including USB, Ethernet, and HDMI do not work
This Docking Station has two USB-C ports. The USB-C port located on the front panel is for connecting and charging peripherals with USB-C such as a smartphone, up to 18W. When a computer (host) is connected to this USB-C port, it will only provide 18W charging to the computer.
Please connect the computer to the USB-C port located on the rear panel, which provides 80W charging and all connectivity to the computer.
Symptom: Ethernet connection not recognized or stopped working.
Please refer to the article below to trouble shoot the Ethernet.
Symptom: Ethernet keeps disconnecting with certain Dell computers.
Some Dell XPS and Precision models may contain a version of internal Wi-Fi adapters that interfere with the Ethernet connection over USB-C. This issue can be resolved by lowering the power output of the onboard Wi-Fi adapter.
1. Navigate to Control Panel > Device Manager
2. Select Network adapters. Right-click on the Dell wireless adapter.
3. Select Properties. Click on the Advanced tab. Select Power Output and select 75%.
4. Disconnect the cables and multiport adapter, restart the computer, and reconnect everything.
Symptom: Audio is not transmitted to monitor through HDMI
Some monitors do not have built-in speakers. Therefore, audio must be transmitted separately. If audio is supported, please follow the steps below to select the correct playback device:
1) Open the 'Sound' menu by searching or right clicking the sound icon on the taskbar
2) In the Playback Tab, select the display with HDMI
3) Click Set Default
4) Click OK to save the settings
1) Open the Apple Menu and go to System Preferences
2) Click the Sound icon
3) Click the Output tab
4) Select the display with HDMI
Article ID: 113
Last updated: 09 Sep, 2019